New PEX Passed an Air Test, Then the Crimps Started Weeping: A How-To on Street Pressure, PRVs and Testing at Working Pressure
Geography note: this piece is about the model International Residential Code (IRC), not one state. Code editions and amendments vary, so check what your jurisdiction has adopted.
What happened
On October 29, a poster on r/Plumbing asked a simple question: can high water pressure cause small weeping leaks in PEX? Here's a summary of what they described. A new-construction house, plumbed entirely in PEX, passed an air test at rough-in that held 70 psi. After the water was turned on, slow weeps showed up at a long list of crimp joints. Street pressure turned out to be well over 80 psi. The plumber installed a pressure-reducing valve (PRV) set to 55 psi, and according to the poster the weeping stopped and the meter's low-flow indicator held steady. Hard Hat Report covered the thread the same day.
We can't diagnose a house from a Reddit post. The leaks might have come from marginal crimps, from pressure, or from both. What the case does show is a gap any builder can close: the rough-in test ran below the pressure the system actually saw in service. Here's how to keep that from happening on your job.
Why it matters
A weep at a crimp ring behind finished drywall becomes a callback, a drywall patch and maybe a mold claim. On a production build with dozens of joints, one bad assumption about street pressure can turn into a punch list across the whole house. Pressure regulation and testing are code items, so they belong in the plumbing scope and in your inspection checklist.
Step 1: Measure static pressure before you rough in
Screw a pressure gauge onto an outdoor hose bib or a test port with nothing running, and write down the reading. Ask the water utility what range to expect at that address, since pressure can swing between day and night. Do this on the first site visit, not after the walls are closed.
Step 2: If it's over 80 psi, put a PRV in the scope
The IRC sets the limit. Under P2903.3.2 in the 2024 IRC (numbered P2903.3.1 in earlier editions), static water pressure can't exceed 80 psi. Where the main's pressure is higher, an approved pressure-reducing valve conforming to ASSE 1003 or CSA B356 must be installed on the domestic water branch main or riser at the connection to the water service pipe (2024 IRC Ch. 29 via UpCodes).
Price the PRV into the bid. Don't leave it for a change order after the leaks start.
Step 3: Handle thermal expansion when you add a PRV
Many PRVs and check valves create a closed system. The IRC requires a means of controlling increased pressure from thermal expansion:
- where water pressure downstream of a PRV can exceed the PRV's setting (P2903.4.1), and
- where a backflow preventer, check valve or other device stops pressure from relieving back into the main, and a storage water heater is installed (P2903.4.2).
In practice that usually means an expansion tank or another approved device. Check your local amendments.
Step 4: Test at or above working pressure, and with water unless the manufacturer allows air
The IRC's test for water supply systems (P2503.7) calls for testing the system tight under a water pressure of not less than the working pressure it will be used under. As an alternative for systems other than plastic, an air test of at least 50 psi is allowed. The test is held for at least 15 minutes, using water from a potable source. For PEX, the 2024 text adds an exception: compressed gas testing is allowed only where the pipe and fitting manufacturers' instructions specifically authorize it, and only where no other law prohibits it (2024 IRC Ch. 25 via UpCodes).
Here's the lesson from the thread. If the street delivers more than 80 psi and the PRV isn't in yet, a 70 psi test didn't prove the joints at the pressure they would actually face. Before you choose a test method, read the PEX and fitting manufacturers' instructions and confirm with your inspector.
Step 5: Gauge every crimp ring
Crimp systems depend on the ring being fully and evenly compressed. One fitting maker's crimp instructions for ASTM F1807 and F2159 fittings tell installers to check every ring connection with a go/no-go gauge, keep the ring about 1/8 inch from the end of the tubing, pressure test according to local codes, and cut off and replace any fitting that leaks rather than trying to fix it in place (Jones Stephens PEX crimp instructions). Calibrate the crimp tool on the schedule the manufacturer specifies. A tool that's out of adjustment will make a whole house of marginal crimps.
Step 6: Document it
Write the static reading, the PRV setting, the expansion-control device, the test medium, test pressure and hold time, and who witnessed it on the permit card or job log. If a weep shows up after closeout, that record shows what was tested and at what pressure.
Who's affected
- Plumbing contractors running PEX crimp or clamp systems on new construction.
- General contractors and builders who sign off on rough-in schedules and own the callback when a weep stains a ceiling.
- Inspectors and owners in areas with high utility pressure.
Who's responsible
Most states and many localities require plumbers to be licensed (BLS, Plumbers). A licensed plumbing contractor's scope usually covers pressure regulation and testing. If you're a GC, check that the plumbing sub's bid includes the static reading, the PRV and the expansion device, and that the license on the permit matches the company doing the work.
The bottom line
Measure street pressure first. If it's over 80 psi, a PRV is a code requirement, and it needs expansion control with it. Test at the pressure the system will really see, using the method the PEX maker allows, and gauge every ring. That's cheaper than opening finished walls.
IQS — connecting construction businesses with state-licensed qualifiers.
Sources
- r/Plumbing — "Can high water pressure cause small weeping leaks in Pex??" (Oct. 29, 2026)
- Hard Hat Report — New PEX passed an air test, then dozens of crimps wept: why street pressure over 80 psi matters (Oct. 29, 2026)
- UpCodes — 2024 IRC Chapter 29, Water Supply and Distribution (P2903.3.2, P2903.4)
- UpCodes — 2024 IRC Chapter 25, Plumbing Administration (P2503.7)
- Jones Stephens — PEX crimp fitting installation instructions (ASTM F1807/F2159)
- U.S. Bureau of Labor Statistics — Occupational Outlook Handbook, Plumbers, Pipefitters, and Steamfitters
Share this article
Need a licensed qualifier for your business? Request a qualifier match. Hold a license and want to qualify a company? Start here.
Follow International Qualifier Search for more on Facebook, LinkedIn, YouTube, and Instagram.
